 | Home > Technical > How-To: Side locker Nakatanenga |
 
|
|
|
| ARC99 Member Since: 19 Feb 2013 Location: North Yorkshire Posts: 1831   
|
looking at the photo I believe the reference is to the chain. Don't make old people mad. We don't like being old in the first place, so it doesn't take much to  us off.
Richard |
||
6th Apr 2016 1:33pm |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247  
|
This one:  Click image to enlarge 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
6th Apr 2016 1:35pm |
|
| nakatanenga Member Since: 12 Nov 2010 Location: Neumarkt Posts: 546 
|
Sorry, that's a hanger from the powdercoater. WANTED:
SII or SIII in max 1.5k |
||
|
6th Apr 2016 1:48pm |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
 ok 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
6th Apr 2016 1:52pm |
|
| Supacat Member Since: 16 Oct 2012 Location: West Yorkshire Posts: 11018 
|
4.5 hours - are you cutting the hole with a rusty bread knife? |
||
|
6th Apr 2016 7:14pm |
|
| L110CDL Member Since: 31 Oct 2015 Location: Devon Posts: 10728 
|
Hi i have not got the side locker that you have got, but when i fitted my 2 lockers (one each side) i made a bracket up to bolt on the back of the box to the landy chassis and put some Stixall (same as Tiger Seal but cheaper) around the bolt heads in the box to keep the water out, which has worked 100%, hope this helps you
 1996 Golf Blue 300Tdi 110 Pick up.
Keeper. Clayton. |
||
|
6th Apr 2016 9:40pm |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
Thx for the tip. 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
7th Apr 2016 5:10am |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
The drilling is done.
To fit it in the right side of a 2015 puma, you have about 15mm margin to place the box. If you go higher, you have to go more to the back, and then the fuel filter gets in the way. Tomorrow I'll make the support so the box can rest on the chassis and be fixed to the support. The fuel filter protector also needs a cut or the locker will not fit. If you have rock-sliders you can't place the locker lower than 30mm from the bottom of the side panel, or you won't be able to open the door wide enough. I also have the impression that the door is quite far from the side panel. Seems like the locker should not be pushed in the whole but place via the bottem and then push it outwards, but there is not enough space to make that possible. Once done, more photo's will follow. Click image to enlarge Click image to enlarge Click image to enlarge Click image to enlarge Click image to enlarge Click image to enlarge Click image to enlarge 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
7th Apr 2016 4:26pm |
|
| L110CDL Member Since: 31 Oct 2015 Location: Devon Posts: 10728
|
Your making good progress there, you get very nervous when you are cutting the hole out, even when you have measured ten times
1996 Golf Blue 300Tdi 110 Pick up.
Keeper. Clayton. |
||
|
7th Apr 2016 9:35pm |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
oooh yes.. It took me a while before I made the first cut on the final measurement
Today I'll try to get the box installed from below and push it outwards, so the door is closer to the body. Kept me awake for some hours  28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
8th Apr 2016 6:04am |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
Job done, but not straight forward. The locks were to high in the door. Shortening the lips heated them up, so the welding got loose.
So, that's how you get 4,5 hrs 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
8th Apr 2016 11:43am |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
http://www.defender2.net/forum/post522737.html#522737
Full report can be read on the website. 28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
10th Apr 2016 12:04pm |
|
| Mo Murphy Member Since: 01 Jun 2008 Location: Letchworth Garden City, Herts Posts: 2214 
|
Good work penguin, sometimes you have to be brave 😊
Nice to see you fitting stuff yourself, too many people miss out on the 'fun' of installation by paying someone else to do it. Well done
Mo The Land Rover 90 - Many are called, few are chosen. 50 Shades of Pennine Grey |
||
|
10th Apr 2016 12:33pm |
|
| Penguin Member Since: 08 Dec 2014 Location: Tienen Posts: 247
|
thank you
28/02 - Loss of a good friend...
In a time of chimpanzees, I was a penguin. |
||
|
10th Apr 2016 12:37pm |
|
|
|
| All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
