DEFENDER2.NET - View topic - TDI 200 Fuel Injector Pump

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Tdi > TDI 200 Fuel Injector Pump

Page 8 of 10

Print this entire topic ·

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

1990 Defender 110 200 Tdi SW Santorini Black

The oil level is sufficient as I just changed it on Sunday.

Due to the rain yesterday, the oily area was cleaned up. I checked this morning and noticed that there seemed to be no oil leaking from there.

Could it be that the axle breather caused the oil leak when the water level reached it?

Will monitor closely and check again.

Mine was drum brake.

Thank you.

14th Jun 2024 3:31am

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

I checked this evening, and it is still leaking (see attached photo – I suspect the leak is coming from the area marked with the red circle).

I am thinking of opening it up and checking on Monday.

Click image to enlarge

15th Jun 2024 12:48pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3421

2012 Defender 90 Puma 2.2 CSW Santorini Black

99% is the dust cap on the end of the drive member. 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

15th Jun 2024 5:10pm

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Alright, I will update again.

By the way, I wanted to ask if you have come across this second drain plug with a filter on an LT77 (as seen in the attached photo - already cleaned up) leaking?

Click image to enlarge

Is it because the leaks from transfer box - O ring? - as seen in the attached photo. But the colour of fluid was red ATF.

Click image to enlarge

Also, regarding this filter (as seen in the attached photo), the copper washer cannot fit onto the bolt at all. Is the copper better than fibre washer?

Thank you.

16th Jun 2024 1:19pm

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Dinnu wrote:
99% is the dust cap on the end of the drive member.

Hi Bro,

You are right. The dust cap was cracked and broken, as shown in the attached photo.

Click image to enlarge

Click image to enlarge

Do you know the part number of this? Is it same as front wheel dust cap?

Thank you.

18th Jun 2024 12:02pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3421

I think FRC4377 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

18th Jun 2024 12:28pm

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

thanks, got it.

18th Jun 2024 12:34pm

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Hi Dinnu,

Which parts or areas should I check when the reverse gear makes a clunking sound near the rear axle?

For your information, I just changed the A-frame 1.5 years ago, so it should not be a problem.

And the drive shaft looks great as well. Could it be the half shaft or the flanges?

Thank you.

2nd Jul 2024 2:01pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3421

Wear in the drive members/halfshaft splines is one of the reasons for the rear end clunk.
I would not exclude the A frame ball joint unless you are sure that a good quality ball joint was installed.
Good also to check the trailing arm bushes. 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

3rd Jul 2024 10:37am

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Ok, the A-frame is from Delphi, but it's not greasable.

By the way, do you know the part number for the rear hub seal and stub seal? Are there any gaskets I need to purchase if I remove everything and replace the hub and stub seal?

The other side of the wheel is leaking now.

Click image to enlarge

3rd Jul 2024 11:09am

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Dinnu wrote:
Wear in the drive members/halfshaft splines is one of the reasons for the rear end clunk.
I would not exclude the A frame ball joint unless you are sure that a good quality ball joint was installed.
Good also to check the trailing arm bushes.

One more: I noticed that there is also a clunk sound when i turn left or right.

3rd Jul 2024 11:57am

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3421

Have a look at https://www.lrworkshop.com/diagrams/land-r...0455_52627

I hope its the correct for your axle.

Seals are 7 and 12.

You might want to have the drive flange gasket #11 and the lock washer #18. I do not know how 110 is, but my 90 is with a flat stub axle on the rear and a slotted stub axle on the front.

Regarding the clunk sound when you turn left/right. Is it a one clunk, or is it a clicking sound (CV joint clicking?). 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

3rd Jul 2024 3:03pm

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Ok, thank you for the diagram and link. I will check it out.

The sound is like clicking, and it seems to come from the rear axle. This week Monday, we went to Fraser Hill and stopped at KKB. Before reaching Fraser Hill, I noticed a burnt smell coming from the rear passenger side wheel.

When the gear is in neutral and I let the car reverse automatically because it was on a ramp, it also makes a clunking sound.

then the axle oil was brown milky water that already mixed with water (I just change all yesterday). Not sure because of that, it got burnt smell or something else.

3rd Jul 2024 4:37pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3421

Burning or clunking sound, when freewheeling backwards might either be a dragging brake shoe or a wheel bearing on its way out. 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

4th Jul 2024 4:55am

cykoh85

Member Since: 25 Apr 2022
Location: Selangor
Posts: 143

Ok, I will look into these two parts. If it's the wheel bearing, can I change just one side, or do I have to change both sides?

4th Jul 2024 5:24am

Page 8 of 10

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum