| Author |
Message |
 Replacement doors |
Oldowner
 21st Mar 2025 2:42am
|
Forum: Maintenance & Modifications · Replies: 6 · Views: 395 · Subject: Replacement doors |
| I wouldn’t fit the old pre 2005 style doors even if they were free! |
| Replacing Front Nose Panel |
Oldowner
9th Mar 2025 4:07am
|
Forum: Maintenance & Modifications · Replies: 5 · Views: 580 · Subject: Replacing Front Nose Panel |
| It is really an easy job. I would bother replacing the entire wing, I used to do loads. Replace spot welds on inner face with countersunk m5 rivets. Drill out spot welds on headlamp mounting pressing, ... |
| [For Sale] Factory XS cubby with padded lid |
Oldowner
22nd Feb 2025 7:31pm
|
Forum: For Sale & Wanted · Replies: 1 · Views: 557 · Subject: [For Sale] Factory XS cubby with padded lid |
| Super rare genuine Land Rover TDCi cubby box, with the factory padded lid, which I believe was only fitted as an upgrade to the top of the range adventure / landmark etc. 99% of Pumas including the XS ... |
| New Door Hinges - Any Experience? |
Oldowner
12th Feb 2025 5:57pm
|
Forum: Maintenance & Modifications · Replies: 37 · Views: 7511 · Subject: New Door Hinges - Any Experience? |
| I had to replace a set of hinges on a neglected 2015 last month. I bought three genuine hinges and as one of the hinges was out of stock, bought a Britpart pattern one as a temporary measure. It pains ... |
| TDi injector pump head seal leaking. Replacing the O ring. |
Oldowner
6th Feb 2025 11:22am
|
Forum: Tdi · Replies: 2 · Views: 395 · Subject: TDi injector pump head seal leaking. Replacing the O ring. |
I have done quite a few with this method and never had a problem however am always careful to just reveal the o ring and jab it with a sharp pick to remove it.
I have at least five spare 300tdi inj ... |
| Defender 90 2015 GKN OEM rear prop shaft UJ |
Oldowner
2nd Feb 2025 8:21am
|
Forum: Technical · Replies: 3 · Views: 374 · Subject: Defender 90 2015 GKN OEM rear prop shaft UJ |
| I have cut them in the past |
| [For Sale] Steering box - 4 bolt type for refurb. |
Oldowner
1st Feb 2025 6:51am
|
Forum: For Sale & Wanted · Replies: 12 · Views: 2313 · Subject: [For Sale] Steering box - 4 bolt type for refurb. |
I fitted an SP one to a 300tdi 90 recently. Absolute nightmare.
Firstly the input shaft casting is now held by four M10 bolts. The bottom two bolts fouled the coilspring seat reinforcing gussets o ... |
| [Wanted] Ex sse defender 130 |
Oldowner
30th Jan 2025 9:47am
|
Forum: For Sale & Wanted · Replies: 10 · Views: 1175 · Subject: [Wanted] Ex sse defender 130 |
Good to know there’s still some in use!
They are a dying breed, National Grid (WPD) are jettisoning their fleet rapidly, I still have a 110 which has been given a years reprieve and will most lik ... |
| Rattle behind/under drivers seat |
Oldowner
20th Jan 2025 5:23pm
|
Forum: Puma (Tdci) · Replies: 33 · Views: 1903 · Subject: Rattle behind/under drivers seat |
Those plastic things were only fitted to XS models and can be discarded with any apparent detriment. They are probably intended to reduce noise but don't seem to make any difference.
They all had t ... |
| Steering Angle Sensor |
Oldowner
20th Jan 2025 5:21pm
|
Forum: Puma (Tdci) · Replies: 15 · Views: 4350 · Subject: Steering Angle Sensor |
| That is how I have always done it with Nanocom and works fine when I’ve done it. Can’t see it needing calibration, even when I’ve fitted brand new replacement steering sensors you just turn it u ... |
| Rattle behind/under drivers seat |
Oldowner
19th Jan 2025 2:49am
|
Forum: Puma (Tdci) · Replies: 33 · Views: 1903 · Subject: Rattle behind/under drivers seat |
| Yes, stones can get stuck in the plastic under shield. It’s only held by the four bolts visible which screw into threaded inserts in the seatbox. |
| Steering Angle Sensor |
Oldowner
19th Jan 2025 2:45am
|
Forum: Puma (Tdci) · Replies: 15 · Views: 4350 · Subject: Steering Angle Sensor |
When you had the ignition barrel changed did they remove the steering wheel ? I’m assuming they did.
If they did and inadvertently moved the steering angle sensor on the steering column then it wil ... |
| [For Sale] Bowler 90 rear mudflap brackets |
Oldowner
13th Jan 2025 11:13pm
|
Forum: For Sale & Wanted · Replies: 0 · Views: 373 · Subject: [For Sale] Bowler 90 rear mudflap brackets |
| Bowler mudflap brackets. Removed from my Bowler 90 as the powdercoating was starting to peel, shot blasted and hot zinc sprayed (they couldn’t be galvanised as the small hole details would clog when ... |
| Diff Clunk! |
Oldowner
4th Jan 2025 10:45pm
|
Forum: Puma (Tdci) · Replies: 20 · Views: 1724 · Subject: Re: Diff Clunk! |
... Ashcroft website say there can be a friction welding issue with the type of diff? ...
Crossed wires here, I think. There is a welding issue with TDCi front axles, well documented here on the ... |
| Replacing sunroof seal |
Oldowner
21st Dec 2024 8:37am
|
Forum: Td5 · Replies: 29 · Views: 11908 · Subject: Replacing sunroof seal |
| I have found that the original seal for the twist handle sunroof is long lasting, usually what causes leaks is where the roof hasn’t been operated for six months over the winter, the seal can stick ... |
| |
