↓ Advertise on Defender2 ↓

Home > Maintenance & Modifications > Wheel bearing change
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Craig



Member Since: 10 Oct 2014
Location: Portland, Dorset
Posts: 18
England 
Wheel bearing change
Had to change the wheel bearing for the MOT, I also changed the hub oil seals as they where leaking. The only thing is when I got it all back together I couldn't get the half shalf out enough to put the C clip back on, the driving flange was on and bolted down, I could feel the groove that the clip sits in with a finger nail but not enough was protruding the driving flange for the c clip to locate into. Any ideas on where I've gone wrong?

[URL=]
Click image to enlarge[/URL]

Admin note: this post has had its images recovered from a money grabbing photo hosting site and reinstated Mr. Green
Post #392326 25th Jan 2015 10:45am
View user's profile Send private message View poster's gallery Reply with quote
Lou Sparts



Member Since: 15 Apr 2012
Location: Kent
Posts: 1501
United Kingdom 2005 Defender 90 Td5 XS CSW Zambezi Silver
It's been some time since I've done that job but does the shaft have an internal thread in it that you can put a bolt in and pull the shaft out ? I think shaggy dog had a similar problem a week or so back and took out the opposite shaft and pushed a length of copper pipe through to push the shaft out !

Necessity is the mother of invention Thumbs Up 2005 Td5 90 XS

Steve
Post #392328 25th Jan 2015 11:02am
View user's profile Send private message View poster's gallery Reply with quote
Craig



Member Since: 10 Oct 2014
Location: Portland, Dorset
Posts: 18
England 
Yep, I had a bolt in the thread and a slide hammer on it and it didn't budge! Would be a right pain in the arse to strip the other side down to push this one out, and what then if the other side did the same apon reassembly??? Something I could try if all else fails! Why is it the simplest jobs turn out to be the most problematic?
Post #392330 25th Jan 2015 11:07am
View user's profile Send private message View poster's gallery Reply with quote
Lou Sparts



Member Since: 15 Apr 2012
Location: Kent
Posts: 1501
United Kingdom 2005 Defender 90 Td5 XS CSW Zambezi Silver
How about removing flange and shaft and assembling them together then put the shaft back in with the flange already on it ? 2005 Td5 90 XS

Steve
Post #392331 25th Jan 2015 11:10am
View user's profile Send private message View poster's gallery Reply with quote
munch90



Member Since: 26 Oct 2013
Location: guildford
Posts: 3558
England 
Take it you might know this but normally screw a bolt in the centre then just pull out by hand , you want need a slide hammer normally ( well i never have anyway

Cant remember if the thrust washer for the cv has a wrong or right way round , some washers have a tapered inner
Post #392563 25th Jan 2015 8:26pm
View user's profile Send private message View poster's gallery Reply with quote
blackwolf



Member Since: 03 Nov 2009
Location: South West England
Posts: 17384
United Kingdom 2007 Defender 110 Puma 2.4 DCPU Stornoway Grey
Are you absolutely sure that the hub assembly is back on the stub axle correctly? If for some reason the hub isn't seating correctly (ie it hasn't gone on far enough) - for example if the outer race of the inner bearing isn't properly installed - you would have this problem. I can't immediately think of any other reason.
Post #392607 25th Jan 2015 10:33pm
View user's profile Send private message View poster's gallery Reply with quote
roel



Member Since: 08 Aug 2009
Location: Lelystad
Posts: 2039
Netherlands 2003 Defender 90 Td5 PU Caledonian Blue
Nice 1997 or 1998 CT Defender Thumbs Up
As said above I think your bearings are not installed correctly. Roel

1984 90 2.5 na Diesel - RR V8 (1994-2001)
1997 Camel Trophy Discovery 300TDI (2001-2009)
2005 G4 Discovery III 4.4 V8 (2008-2018) It's gone but it still hurts.
2003 90 Td5 (2009-now)
Post #393400 28th Jan 2015 7:13pm
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8030
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
just take the hub off and try and pull it out, if still wont come take stub axle off and check seating in back.

Sometimes they get pushed in on assembly and dont come back out until it is stripped again, just keep hold of it on the 2nd assembly.

probably nothing fitted wrong, its just been stubourn. Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #393421 28th Jan 2015 8:14pm
View user's profile Send private message View poster's gallery Reply with quote
Craig



Member Since: 10 Oct 2014
Location: Portland, Dorset
Posts: 18
England 
Thanks for all the suggestions really appreciated, I will have it part again hopefully this weekend and try some stuff out. Cheers
Post #393440 28th Jan 2015 8:42pm
View user's profile Send private message View poster's gallery Reply with quote
x-isle



Member Since: 26 May 2011
Location: Midlands
Posts: 1327
Wales 2007 Defender 110 Puma 2.4 XS CSW Santorini Black
Ok, it's beat me. How on earth did you get the truck up on those front stands? Craig Rogers

2007 Puma 110 XS
2011 Evoque Coupe Dynamic Lux
www.craigrogers.photography
Post #393696 29th Jan 2015 4:03pm
View user's profile Send private message View poster's gallery Reply with quote
mk1collector



Member Since: 17 Sep 2009
Location: West Yorkshire
Posts: 6769
England 2004 Defender 110 Td5 CSW Bonatti Grey
I'm guessing with the other half of the ramp setup that's still holding the wheel just at the right of the picture Mr. Green
Post #393698 29th Jan 2015 4:09pm
View user's profile Send private message View poster's gallery Reply with quote
munch90



Member Since: 26 Oct 2013
Location: guildford
Posts: 3558
England 
use the other pair of colum lifts ( you can just see the other one with the wheel still on it ) lift on the wheel then lower on to stands then remove the wheels
Post #393699 29th Jan 2015 4:09pm
View user's profile Send private message View poster's gallery Reply with quote
x-isle



Member Since: 26 May 2011
Location: Midlands
Posts: 1327
Wales 2007 Defender 110 Puma 2.4 XS CSW Santorini Black
Agh, right I can see now. Didn't notice the ramps moved out of the way Craig Rogers

2007 Puma 110 XS
2011 Evoque Coupe Dynamic Lux
www.craigrogers.photography
Post #393701 29th Jan 2015 4:14pm
View user's profile Send private message View poster's gallery Reply with quote
taazzukcb



Member Since: 30 Aug 2013
Location: Derbyshire
Posts: 663
United Kingdom 2004 Defender 110 Td5 DCPU Stornoway Grey
I assume they're not new drive members? (The earlier thicker ones vs the later thin ones?)
Post #393711 29th Jan 2015 4:38pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums