↓ Advertise on Defender2 ↓

Home > In Car Electronics (L663) > Rear Windows Activation 110 Hard Top
Post Reply  Down to end
Page 3 of 3 <123
Print this entire topic · 
mattlidster



Member Since: 17 Jan 2017
Location: UK
Posts: 17
United Kingdom 1989 Defender 90 300 Tdi ST Alpine White
Did you have any luck with the rear door puddle lights? The new loom I fitted has the wires there but they dont come on. I have even tried leaving the 2 that did work as a commercial but adding 2 new lights to the doors but still no luck. I cant see anything obvious in the CCF that could be changed.
Post #1019515 29th Dec 2023 10:42am
View user's profile Send private message View poster's gallery Reply with quote
Paladino



Member Since: 07 Dec 2022
Location: Serbia
Posts: 30
Hi, unfortunately it's not coding related - the positive wire for the puddle light that goes from the bcm to the door connector is missing on commercial vehicles.
Post #1019583 29th Dec 2023 11:18pm
View user's profile Send private message View poster's gallery Reply with quote
mattlidster



Member Since: 17 Jan 2017
Location: UK
Posts: 17
United Kingdom 1989 Defender 90 300 Tdi ST Alpine White
Ah ok, does that mean you cant get the ambient LED lights to work either with this additional loom LR130014?
Post #1019603 30th Dec 2023 8:12am
View user's profile Send private message View poster's gallery Reply with quote
Paladino



Member Since: 07 Dec 2022
Location: Serbia
Posts: 30
Yep. You will need additional wiring. For the ambient leds - lin comes from the door module, earth is also in the door i believe, but the power comes from the bcm.
Post #1019608 30th Dec 2023 8:49am
View user's profile Send private message View poster's gallery Reply with quote
Ducatirider2024



Member Since: 18 Sep 2024
Location: Bolton
Posts: 1
United Kingdom 
L663 Window conversion
I am looking at starting my own project on my L663 2024 and have a couple of questions if ok

Did you install the door close handle and new panel or just cut the panel to take the switch
How do I do the config
Did you use a disco switch in the front in the end and if so what year did you go for

Also fancy putting two single seats in the rear with hot and cold do you think this is possible from what you did when you installed yours and how dod you get the heat and cold work on your seats

Appreciate any guidance thank you paul



mattlidster wrote:
Mine is a 2022

Removed both rear door wiring looms completely.

Parts used so far

New wiring loom Drivers side rear door LR171801
New wiring loom Passenger side rear door LR171817 ( I think that's the right way round!)
2 X new switches LR059773
2 X new switch facias LR064090
New door Moulding round small window LR149591
New door Moulding round small window LR149592
New front door window switch with mirrors and memory seats LR130144

Changed Car Config File via IIDTool

MultiCAN-634 MovingWindows
Four Moving Windows


EUCD-109 Power Windows, Front/Rear
DCU Powered Front & Rear Windows
Post #1046073 18th Sep 2024 8:16am
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 3 of 3 <123
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums