DEFENDER2.NET - View topic - Relay Plug Holders

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Technical > Relay Plug Holders - Repair

Page 2 of 2

Print this entire topic ·

PaulMc

Member Since: 17 Jan 2009
Location: Kent
Posts: 502

3-Way Components can also supply some of the Lucas-Rists relay bases -

https://www.3waycomponents.co.uk/Relay-Hol...ay-Holders

Including the bracketed type, that will fit to the screw mountings on the bottom of the TD5 centre fuse box panels YQU104850 (1999MY) and YQU000200 (2002MY) -

https://www.3waycomponents.co.uk/Relay-Hol...racket-Kit

They also have an ebay shop - http://www.ebaystores.co.uk/3waycomponents

. Paul.
1989 Arles Blue 2.5TD 110 Hardtop
1999 Epsom Green Discovery II 4.0 V8i 'XS'

13th Apr 2020 3:22pm

LANDROVER

Member Since: 13 Feb 2016
Location: EAST OF ENGLAND
Posts: 208

Martin wrote:
Durite aren't original, they are an aftermarket supplier, but there is nothing "wrong" with them as components.

Best bet if you can is to photo what you have and what you need to replace.

Click image to enlarge

Click image to enlarge

I decided to fit my new relays and plugs.

I replaced the 2 yellow relays and plugs. Removed some strange solder extensions in the wires!

The Black relay in the picture which is cable tied to the loom I wanted to fit a holder and fasten in the box properly.

Some wires are a bit too big for my new spades but I think I got them nicely crimped...but these ones are far too big?
(Brown Wire)

So I found some bigger spades but didn't realise as I was rushing that they are smaller. Tried to fit the plug and noticed that the relay has 2 big spades and 2 smaller ones.

Not sure what this relay is for and whether its correct to have bigger spades? I have attached a picture.

I've given up today as it's too cold

Some of the plugs where badly corroded and one wire snapped in my hands and one pulled out because of a bad crimp so think I may have found the source of my problems

Thank you for your help and patience. I've been off the tools so long and on my own. I don't want to ruin my poor Land Rover with my own incompetence

#EDIT#
These are the plugs spades I'm using from 3waycomp.

Click image to enlarge

10th May 2020 4:40pm

Martin
Site Admin

Member Since: 02 Apr 2007
Location: Hook Norton
Posts: 6611

2015 Defender 90 Puma 2.2 XS CSW Montalcino Red

As far as I can remember, there are only two uses of the 70A relay you've got there on a Td5 (it is the correct relay).

One is the glow plugs (C0215 in photo below). This has brown and yellow/black 6.0mm² wires (the large power ones) and smaller brown/orange and green/blue wires for the coil.

It should be clipped next to the fuse box as shown.

The other (C0508) is for the ABS pump which you may or may not have - probably not as you only mention one. This has brown/white and brown/red 4.0mm² and 3.0mm² wires (the large power ones) and smaller black and white/orange wires for the coil.

Click image to enlarge

The socket (YPP10005) isn't available from LR nor can I track it down anywhere else.

3way components don't have the same holder as the original part either but they do have an alternative kit:

https://www.3waycomponents.co.uk/Relay-Hol...racket-Kit

1988 90 Td5 NAS soft top

2015 D90 XS SW

11th May 2020 9:08am

PaulMc

Member Since: 17 Jan 2009
Location: Kent
Posts: 502

I can supply YPP10005 with terminals to suit up to 6mm² cable.

Click image to enlarge

. Paul.
1989 Arles Blue 2.5TD 110 Hardtop
1999 Epsom Green Discovery II 4.0 V8i 'XS'

Last edited by PaulMc on 11th May 2020 12:59pm. Edited 2 times in total

11th May 2020 10:20am

Martin
Site Admin

Member Since: 02 Apr 2007
Location: Hook Norton
Posts: 6611

1988 90 Td5 NAS soft top

2015 D90 XS SW

11th May 2020 11:00am

LANDROVER

Member Since: 13 Feb 2016
Location: EAST OF ENGLAND
Posts: 208

Thank you Martin.

I've now ordered the relay base from them and the following relay;
Automotive Relay 12V 70Amp 4 Pin Normally Open - Genuine Tyco/TE Part

It looks like the new holder/socket does not hook only the tabs in the relay box, which is a shame.

Hopefully I can get it all back together nicely! It's the first time in over a year the Land Rover has had time off

I Feel guilty having it all in bits!

11th May 2020 5:25pm

LANDROVER

Member Since: 13 Feb 2016
Location: EAST OF ENGLAND
Posts: 208

PaulMc wrote:
I can supply YPP10005 with terminals to suit up to 6mm² cable.

Click image to enlarge

.

Thank you for your reply Paul. I didn't see it until I had ordered. I will drop you a message as I may want one as the one I ordered I don't think fits the tabs in the box. Plus I might want some spares.

11th May 2020 5:30pm

Page 2 of 2

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum