↓ Advertise on Defender2 ↓

Home > Puma (Tdci) > Tdci bonnet pin ripped from bonnet
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Sam smith



Member Since: 12 Aug 2021
Location: Suffolk
Posts: 65
United Kingdom 2009 Defender 110 Puma 2.4 HT Epsom Green
Tdci bonnet pin ripped from bonnet
I recently bought a project defender tdci and the pin has been ripped out of the bonnet which looks like it could be a tricky one to repair but I have to try. Is the pin located directly in the centre of this middle section any recommendations on best course of action?
Photo attached
Many thanks
Post #1000650 18th Jul 2023 7:13am
View user's profile Send private message View poster's gallery Reply with quote
diesel_jim



Member Since: 13 Oct 2008
Location: hiding
Posts: 6092
United Kingdom 2006 Defender 110 Td5 SW Epsom Green
Those pins are screwed in, so maybe get a nut of the same thread, weld it to a piece of flat metal (with a hold drilled trough of course) and slide it up beind the damaged metal and rivet/weld it into placee?
Post #1000656 18th Jul 2023 7:45am
View user's profile Send private message View poster's gallery Reply with quote
Linds Hanson



Member Since: 16 Jan 2021
Location: Cornwall
Posts: 486
United Kingdom 
Your only easy option is a flat plate with nut welded on the back to except the bonnet striker and then two rivnut fixings to underside of bonnet. However you do it make sure the pin can withstand the windforce applied to the bonnet at motorway speeds
Post #1000668 18th Jul 2023 9:51am
View user's profile Send private message View poster's gallery Reply with quote
Sam smith



Member Since: 12 Aug 2021
Location: Suffolk
Posts: 65
United Kingdom 2009 Defender 110 Puma 2.4 HT Epsom Green
yeah that is a bit of a concern but hopefully i can make it as strong as oem i think my bigger concern is the alignment of the pin and height of it. i assume the pin threaded bit goes dead centre of the central support or is it off centre? i also assume that the metal braket bit it sits on should be level with all the others along the edge of the bonnet?
many thanks
Post #1000777 18th Jul 2023 8:54pm
View user's profile Send private message View poster's gallery Reply with quote
Sam smith



Member Since: 12 Aug 2021
Location: Suffolk
Posts: 65
United Kingdom 2009 Defender 110 Puma 2.4 HT Epsom Green
diesel_jim wrote:
Those pins are screwed in, so maybe get a nut of the same thread, weld it to a piece of flat metal (with a hold drilled trough of course) and slide it up beind the damaged metal and rivet/weld it into placee?


i take it it is meant to go dead centre of that supportive bracket? and the height should be the same as the others?
cheers
Post #1000778 18th Jul 2023 8:54pm
View user's profile Send private message View poster's gallery Reply with quote
NickMc



Member Since: 01 Oct 2014
Location: Norn Iron
Posts: 1624
Northern Ireland 2006 Defender 90 Td5 HT Bonatti Grey
It’s flush with the rest yes and central.
Post #1000787 18th Jul 2023 9:13pm
View user's profile Send private message View poster's gallery Reply with quote
Sam smith



Member Since: 12 Aug 2021
Location: Suffolk
Posts: 65
United Kingdom 2009 Defender 110 Puma 2.4 HT Epsom Green
ok great thank you!
Post #1001055 21st Jul 2023 6:10am
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums