DEFENDER2.NET - View topic - Fitting fuel pickup pipe for webasto in fuel neck

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Maintenance & Modifications > Fitting fuel pickup pipe for webasto in fuel neck - TD5

Page 1 of 1

Print this entire topic ·

AJC

Member Since: 30 Nov 2015
Location: Lancashire
Posts: 1360

Fitting fuel pickup pipe for webasto in fuel neck - TD5

https://www.ebay.co.uk/itm/EBERSPACHER-LAN...1134055406

I have one of the pipes in the link above, has anyone else fit one of these to their defender?

I am just about to do it and was hoping to splice into the fuel neck in situ but as I can't feed into the tank I can't be too accurate with where I make the cut, issue I have is the 110 is on the ramp immobilised and I have nearly a full tank of fuel, got the perfect chance to do it but would be better if tank was empty.

Any advice or measurements as to where it has been tee'd in?

Thanks

14th Nov 2018 6:29am

Ian825

Member Since: 31 Oct 2016
Location: East Yorkshire
Posts: 11

yes I have fitted one, the bit you have fits in the rubber pipe from the filler neck, at the bottom of the rubber pipe.
remove the rubber pipe between the filler neck & the tank inlet, cut the rubber pipe allowing enough at the bottom to secure with jubilee clips on the tank neck & onto the new sleeve, I had to shorten the rubber by approximately 15mm to allow space for the pre heater take off pipe, the old jubilee clips were cut off as siezed so you may find the same, also you need more to attach the rubber hose back to the filler neck and the other end of the new sleeve, the outlet to the pre heater sits at 3 o'clock so the pick up pipe sits in the tank properly.

14th Nov 2018 3:26pm

Ian825

Member Since: 31 Oct 2016
Location: East Yorkshire
Posts: 11

a bit hazy, but shows how it sits in the rubber hose with the take off to three right of the filler tube

14th Nov 2018 3:28pm

Ian825

Member Since: 31 Oct 2016
Location: East Yorkshire
Posts: 11

Click image to enlarge

14th Nov 2018 3:29pm

AJC

Member Since: 30 Nov 2015
Location: Lancashire
Posts: 1360

Fantastic hat Ian, thanks very much for the help

14th Nov 2018 4:09pm

Mdm

Member Since: 11 Sep 2013
Location: Sunny Lancashire
Posts: 1598

on mine i used the fitting on top of the fuel pump .cut end off feed pipe in and seal, been good for years and it sits insides the filter side of things.

the last one i did was thru the pipe similar to the pictures . didn't run the heater if the car was less than 30% full of fuel.

14th Nov 2018 7:46pm

jst

Member Since: 14 Jan 2008
Location: Taunton
Posts: 8018

2011 Defender 110 Puma 2.4 USW Stornoway Grey

Likewise, I have gone in through top of sender on mine with the dedicated webasto pickup. Works when tank is almost empty! Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop

14th Nov 2018 9:45pm

AJC

Member Since: 30 Nov 2015
Location: Lancashire
Posts: 1360

Have you used one of these then James?

https://rover.ebay.com/rover/0/0/0?mpre=ht...1620554507

15th Nov 2018 5:13am

Page 1 of 1

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum