↓ Advertise on Defender2 ↓

Home > Maintenance & Modifications > Two axle breather queries
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
Two axle breather queries
Hi

I've got a MY09 Puma 110 and as far as I can see the breather hose simply pushes into the axle breather, is this correct?

Also, what is the best way to check if the breather is blocked? Blowing air through the hose will obviously clear this, but how do you check the actual breather in the axle? Can it be removed and cleaned?

Many thanks

Mike
Post #241709 7th Jun 2013 1:47pm
View user's profile Send private message View poster's gallery Reply with quote
custom90



Member Since: 21 Jan 2010
Location: South West, England.
Posts: 20318
United Kingdom 
Re: Two axle breather queries
miket wrote:
Hi

I've got a MY09 Puma 110 and as far as I can see the breather hose simply pushes into the axle breather, is this correct?

Yes it is.
miket wrote:

Also, what is the best way to check if the breather is blocked? Blowing air through the hose will obviously clear this, but how do you check the actual breather in the axle? Can it be removed and cleaned?

Many thanks

Mike

Simply remove the pipe and if it's clear it should be fine. AFAIK there is a special technique for removing the pipe as I have done it myself but forgot how to now. Neutral â­ï¸â­ï¸God Bless the USA 🇬🇧🇺🇸 â­ï¸â­ï¸
Post #241744 7th Jun 2013 3:52pm
View user's profile Send private message View poster's gallery Reply with quote
blackwolf



Member Since: 03 Nov 2009
Location: South West England
Posts: 17360
United Kingdom 2007 Defender 110 Puma 2.4 DCPU Stornoway Grey
Disconnect the pipe from the axle. Check axle fitting is clear by probing with a piece of fence wire or similar. Check pipe by placing lips around pipe and blowing.
Post #241754 7th Jun 2013 4:04pm
View user's profile Send private message View poster's gallery Reply with quote
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
Grand, sounds nice and simple...

Cheers

Mike
Post #241780 7th Jun 2013 6:35pm
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8018
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
why do you think it might be blocked? blowing oil from a gasket/seal? Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #241951 8th Jun 2013 11:26am
View user's profile Send private message View poster's gallery Reply with quote
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
Yes, there's a little oil on the inside of the brake that can't have come from anywhere else. It was an MOT fail and so my free MOT (that came with my free service at the dealer) wasn't so free after all...

It's booked in to a local garage (dealer wanted £200 just to diagnose the problem) on Wednesday.

Mike
Post #241956 8th Jun 2013 11:58am
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8018
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
inner hub oil seal in the back of the disc. a pretty simple task to change, wheel off, caliper off, hub off, remove old seal and replace. that particular seal is unlikely to have gone due to a blocked breather. wheel bearings are ok i take it, no advisory on them? Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #242056 8th Jun 2013 7:55pm
View user's profile Send private message View poster's gallery Reply with quote
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
No advisory on anything else - thanks for the brief description of what needs to be done!

Mike
Post #242300 9th Jun 2013 5:56pm
View user's profile Send private message View poster's gallery Reply with quote
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
One last question - to replace the inner hub oil seal do you need to take the half shaft out?
Post #242491 10th Jun 2013 11:20am
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8018
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
no

wheel off
caliper off
dust cap off
half shaft circlip off
drive member bolts out
remove drive member
hub nuts off (will either have one fit spacers with stake nuts or double nuts with locking tabs. fits latter on rebuild)
hub off

invert hub
change rear seal

refit as above in reverse

you can leave the drive member and shaft connected with the circlip and pull the lot, nothing in it really. Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #242614 10th Jun 2013 8:39pm
View user's profile Send private message View poster's gallery Reply with quote
miket



Member Since: 05 Oct 2012
Location: Peak District
Posts: 143
Thanks James, much appreciated.

Mike
Post #242632 10th Jun 2013 9:11pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums