| Author |
Message |
 Bonnet release cable connector boxy thingy, rubbish plastic? |
olivers
 25th May 2023 9:48pm
|
Forum: Puma (Tdci) · Replies: 4 · Views: 960 · Subject: Bonnet release cable connector boxy thingy, rubbish plastic? |
For illustration, here is a 3d printing model that is similar to the part inside the outer case: https://www.thingiverse.com/thing:381034
I doubt that a printed part would be solid enough, but then ... |
| Bonnet release cable connector boxy thingy, rubbish plastic? |
olivers
25th May 2023 9:39pm
|
Forum: Puma (Tdci) · Replies: 4 · Views: 960 · Subject: Bonnet release cable connector boxy thingy, rubbish plastic? |
| Didn’t take a picture, I can grab one tomorrow. This problem is not new, has been discussed here before… without better solutions though! For instance here: https://www.defender2.net/forum/post167 ... |
| Bonnet release cable connector boxy thingy, rubbish plastic? |
olivers
25th May 2023 6:43pm
|
Forum: Puma (Tdci) · Replies: 4 · Views: 960 · Subject: Bonnet release cable connector boxy thingy, rubbish plastic? |
| Second time on my Puma 90 that this stupid little junction thingy fails — part of FSE500080, the bit you can’t buy individually, the little plastic box with a sliding connector that joins the two ... |
| Brake hose from ABS modulator |
olivers
21st Sep 2022 7:25am
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
Fair enough, I see.
Well I started from the position that it's impossible to put in new brake pipes without dismantling much of the engine bay. Using segments occurred to me but that does seem lik ... |
| Brake hose from ABS modulator |
olivers
20th Sep 2022 12:23pm
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
| So did you make your own hoses with these unions? Do you have links for the parts you used? |
| Brake hose from ABS modulator |
olivers
20th Sep 2022 12:12pm
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
I've now had a reply from Furore. Two points:
1. The 10mm union should fit just fine in places where the pipe flange in the photo was previously used. Apparently this is a "dual seated" u ... |
| Brake hose from ABS modulator |
olivers
20th Sep 2022 9:07am
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
there are different flares on brake pipes.
No question! However, in various videos I saw about brake pipes on Land Rovers, I never saw a flange that was not like mine. Never saw different size un ... |
| Brake hose from ABS modulator |
olivers
20th Sep 2022 8:25am
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
The middle one has totally different end - it has opposite cone. For sealing is the inner part, not the outer cone part.
Hm... if that's true then the problem is bigger than I thought. Any clue w ... |
| Brake hose from ABS modulator |
olivers
19th Sep 2022 9:12pm
|
Forum: Puma (Tdci) · Replies: 9 · Views: 2359 · Subject: Brake hose from ABS modulator |
| I’ve finally decided to replace the brake pipes down from the ABS box with hoses — much easier job to get in! Based on previous recommendation I got some hoses made at furoreproducts (https://furo ... |
| Separating disc from hub |
olivers
31st Aug 2022 6:18pm
|
Forum: Puma (Tdci) · Replies: 10 · Views: 2359 · Subject: Separating disc from hub |
| Alright, that’s sorted now - I held the hub in a vice and whacked the brake disc quite a while with a lump hammer before it came off, but eventually it did. Thanks everybody for confirming I wasn’ ... |
| Separating disc from hub |
olivers
30th Aug 2022 8:59pm
|
Forum: Puma (Tdci) · Replies: 10 · Views: 2359 · Subject: Separating disc from hub |
| I’ll get on it tomorrow. Sure it’ll come off - was just wondering if I missed something. I changed a couple discs before, but it’s been a few years and as far as I remember they came off without ... |
| Separating disc from hub |
olivers
30th Aug 2022 8:54pm
|
Forum: Puma (Tdci) · Replies: 10 · Views: 2359 · Subject: Separating disc from hub |
I don’t think the disc is thin enough for that. I’m replacing it because it has disintegrated in a strange way, perhaps because the pad was gone.
https://www.defender2.net/gallery/albums/userpi ... |
| Separating disc from hub |
olivers
30th Aug 2022 8:36pm
|
Forum: Puma (Tdci) · Replies: 10 · Views: 2359 · Subject: Separating disc from hub |
Excellent, thanks. That was my thought, but then I thought I’d better be at least a bit careful  |
| Separating disc from hub |
olivers
30th Aug 2022 8:25pm
|
Forum: Puma (Tdci) · Replies: 10 · Views: 2359 · Subject: Separating disc from hub |
| Replacing (edit: rear) brake discs on my 130. Got the hub off, turn it over, remove five bolts holding the brake disc in place… and then… it doesn’t move a bit. Attempts to persuade it unsuccess ... |
| Half shaft doesn’t want back in |
olivers
6th Apr 2022 7:38am
|
Forum: Maintenance & Modifications · Replies: 13 · Views: 2433 · Subject: Half shaft doesn’t want back in |
| Forgot to say yesterday - all good with the half shaft, it went back in easily enough once I knew which direction to push it. Wiggling it round a bit with some pressure to raise it up at the diff end ... |
| |
