| Author |
Message |
 Transmission noise |
SADS
 18th Jan 2025 7:52am
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
Thank you for sharing this.
Before I fitted the new props (with UJ’s) I mistakenly took the advice from a youtube tutorial that instructed to line all UJ yokes up (in phase). So I did.
Spoke ... |
| Transmission noise |
SADS
17th Jan 2025 9:42am
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
Ah yeah i looked up the handbreak Mod, looks great but unfortunately i do not have this, would a dr handbrake rattle / ring at all?
Tyres were new less than 10k miles ago, same rumble with old set ... |
| Transmission noise |
SADS
15th Jan 2025 8:22pm
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
Not exhaust i dont think, as i have just ensured this isnt touching anything underneath and added new rubbers.
Got drums brakes all round.
Hand brake pads.. not sure, would i need to remove the ... |
| Transmission noise |
SADS
15th Jan 2025 6:58pm
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
I will get under the vehicle ASAP and check this.
Maybe separate, maybe not, but when driving through the gears, if i move into a gear slightly sooner than ideal (say into 5th, but then I cant acce ... |
| Transmission noise |
SADS
12th Jan 2025 9:31am
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
| What about the engine mounts exactly, cracked? Not genuine part? |
| Transmission noise |
SADS
11th Jan 2025 6:54pm
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
Thanks for the replies.
Brand new props which had been greased. Perhaps i should pump more in as suggested, i will give that a go
I haven’t checked wheel bearings, no. I did think it could be ... |
| Transmission noise |
SADS
10th Jan 2025 7:01pm
|
Forum: Tdi · Replies: 16 · Views: 1261 · Subject: Transmission noise |
Hi everyone,
Slowly making improvements to my 200tdi.
I have a loud rumbling vibration / noise between roughly 40-50mph. I replaced both front and rear propshafts/UJ’s for brand new. I did thi ... |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 4:48pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
Haha yep.
Okay, will do. Thanks again. |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 4:41pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
Want to know something funny?
I suddenly realised the low/high gearstick was in neutral… clutch working fine, albeit the biting point is a little low.
Haha thanks the help! |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 3:28pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
Ok, so without the rubber the clutch pedal is sat at 15cm. Im assuming it will require tightening, not loosening to reach 14cm?
There’s about 1-2cm of free play with is an improvement on my old c ... |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 2:46pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
Hi,
I hadn't seen your advice above and was working off what i had read elsewhere. Self bleed system - bottle and pipe off the bleed nipple on slave. Purging the air out the system.
I did the ab ... |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 2:18pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
| Just come back to the forum to see your comments. In the meantime i have been tinkering. System started to bleed once i released the bleed nipple (forgot that bit). So now have resistance on the pedal ... |
| Replacement clutch box / master & slave cylinders |
SADS
23rd Dec 2024 12:08pm
|
Forum: Maintenance & Modifications · Replies: 11 · Views: 664 · Subject: Replacement clutch box / master & slave cylinders |
| I have just installed a replacement clutch pedal box with a master and slave cylinder. Now it’s time to add Dot 4 and bleed the system. I haven’t done this before. Topped up the reservoir with Dot ... |
| Transfer box fill plug seized |
SADS
17th Dec 2024 6:08am
|
Forum: Tdi · Replies: 23 · Views: 1435 · Subject: Transfer box fill plug seized |
| Yep, its the slave cylinder i cant get off. |
| Transfer box fill plug seized |
SADS
16th Dec 2024 6:10pm
|
Forum: Tdi · Replies: 23 · Views: 1435 · Subject: Transfer box fill plug seized |
Now, if anyone has any smart ways to access the top bolt on the clutch slave cylinder…?
I also have a normal master cylinder to replace my current, as well as a LOF master cylinder. Would you thi ... |
| |
