 | Home > Tdi > Replacement Bulkhead experiences |
 
|
|
|
| Andy80 Member Since: 31 May 2013 Location: Essex Posts: 490   
|
Ultra bulkheads look good, has anyone fitted one? Working towards Carry on camping!
|
||
10th Dec 2022 12:27pm |
|
| Mdm Member Since: 11 Sep 2013 Location: Sunny Lancashire Posts: 1599 
|
as above we fitted an ultra one earlier this year to a mates td5 .its ok but lots of little things spoil it and for the money it should be better i think.pm if you want the list of things that needed fettling. but on the upside it did fit onto a richards chassis no issues.
as for sheilder.no one around us fits them..... we have a richards one due to go on a 200 tdi that may arrive before xmas but if not early jan and we will report back how that goes. |
||
|
10th Dec 2022 1:37pm |
|
| Linds Hanson Member Since: 16 Jan 2021 Location: Cornwall Posts: 486
|
Anyone fitted a Maer stainless bulkhead yet? I wonder if they are producing the Hobson bulkheads? They dont seem to list anything later than 300TDI spec and even these are temporarily unavailable?
|
||
|
16th Feb 2023 12:55pm |
|
| Linds Hanson Member Since: 16 Jan 2021 Location: Cornwall Posts: 486
|
How did it go? |
||
|
16th Feb 2023 1:13pm |
|
| Chicken Drumstick Member Since: 17 Aug 2020 Location: Near MK Posts: 724
|
I guess the other consideration would be.... do you actually need to replace the bulkhead?
It is rare (or maybe never) that they completely fail. And you can buy repair panels for the bits that do rust. Might be a heck of a lot less work if you retain the original. |
||
|
16th Feb 2023 1:57pm |
|
| paul 123 Member Since: 10 Jul 2022 Location: norwich Posts: 82 
|
i am collecting a richards chassis bulkhead tomorrow. i hope the quality is the same as the chassis.
|
||
|
16th Feb 2023 3:45pm |
|
| Linds Hanson Member Since: 16 Jan 2021 Location: Cornwall Posts: 486
|
Dont we only use Marsland chassis
 |
||
|
16th Feb 2023 4:10pm |
|
| Mdm Member Since: 11 Sep 2013 Location: Sunny Lancashire Posts: 1599
|
well a little feed back on the 200 tdu richards bulkhead. we got one of the 1st batch. were told to report back any findings so they can improve the next batch.
so the bad news its flipping ace. better than anything else on the market. drops straight on a new chassis. dash holes line up all the rivnuts are in place vent flap holes are drilled out unlike ultra ones square holes for the fixings where they need to be unlike other ones you have to drill and file out. now it did run late due to xmas and tooling issues but well worth the wait. all that was missing was 1 fuel pipe clip hole and they dont drill that one as it varies on tdi where it is. 2 little holes to hold the relays behind the dash needed drilling. i suspect they will add these to the next batch as they have cad drawings and positions to the mm for them. im not saying dont buy any other but wait until you see one of these up close. you can go over and watch them building them up which i did. i have a pile of pics of the lads building them and some of the e coat ones which are very good too. they have even split a few of the test ones to see how far the galv and e coat has covered which is nice. |
||
|
16th Feb 2023 5:47pm |
|
| Linds Hanson Member Since: 16 Jan 2021 Location: Cornwall Posts: 486
|
Sounds good
|
||
|
17th Feb 2023 11:03am |
|
| paul 123 Member Since: 10 Jul 2022 Location: norwich Posts: 82
|
just back from collecting a bulkhead from richards chassis. had the factory tour very interesting. the bulkhead looks top quality.
|
||
|
17th Feb 2023 3:58pm |
|
| Mdm Member Since: 11 Sep 2013 Location: Sunny Lancashire Posts: 1599
|
 Click image to enlarge Click image to enlarge Click image to enlarge Click image to enlarge well we're working our way thru the 90 as we speak. maybe start a new thread as you rebuild yours . i have to say i like that fact that richards will let you have an up close and personal look at what they make, and they welcome feedback. unlike the last one we bought. they new things were missing and couldn't care less . both doors went on without an issue. all the major components fitted spot on. 1 wing on today and it lines up lovely apologies for the wonky seam sealer lines. Click image to enlarge nice not to have to drill holes for grommets and the fact the holes are correct size saves time. extra wax before the wing goes back on. will happily buy another but poss an e coated one a few pics of the work pre galv or e coat they do. the brackets and stampings are a work of art. |
||
|
17th Feb 2023 5:14pm |
|
| Hufflepuff Member Since: 25 Oct 2014 Location: Hampshire Posts: 727 
|
I am quite looking forward to seeing how the Juice Motors team get on with this Shielder bulkhead. I have one myself currently fitted on a Richards Chassis, but I haven't got far enough with it yet to get the doors on to see how they fit. I'm hoping the Juice team don't find too many surprises in part 2 and 3 with it (not yet released).
2005 Td5 90 XS 1989 V8 110 CSW |
||
|
17th Feb 2023 6:17pm |
|
| Gerry Member Since: 22 Oct 2017 Location: north Ireland Posts: 35
|
Have you progressed enough yet to see how everything aligns, doors wings?
|
||
|
11th Mar 2023 12:32pm |
|
| Mdm Member Since: 11 Sep 2013 Location: Sunny Lancashire Posts: 1599
|
the one we fitted is spot on.
no issues with doors or wing fit. so good they are a mate has ordered a 300 tdi one to rebuild his so no rest for us folk helping him. ive seen a link they are at a show somewhere with them soon not sure which one though |
||
|
11th Mar 2023 1:39pm |
|
|
|
| All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
