↓ Advertise on Defender2 ↓

Home > Technical > Nanocom Evolution
Post Reply  Down to end
Page 3 of 3 <123
Print this entire topic · 
Steve B



Member Since: 22 May 2009
Location: Warwickshire
Posts: 586
United Kingdom 2000 Defender 90 Td5 SW Caledonian Blue
Great Very Happy

I guess I should go and read the manual Embarassed

Steve
Post #53571 18th Jan 2011 8:33am
View user's profile Send private message View poster's gallery Reply with quote
Merlin



Member Since: 30 Oct 2010
Location: Newmarket
Posts: 980
United Kingdom 
I’ve installed the codes as shown on the Nanocom site against my product ID this being Licenses 2 & 4, but can’t access the ABS screen. The Nanocom says function blocked. I bought the Nanocom just to monitor the ABS system, as I’ve got an intermittent fault that I want to identify. I thought that the Nanocom came with this installed. Can anyone explain how I get access?

Merlin
Post #53664 18th Jan 2011 5:02pm
View user's profile Send private message View poster's gallery Reply with quote
Lorryman100



Member Since: 01 Oct 2010
Location: Here
Posts: 2686
Quote:

1. Took unit to car and plugged in, On main screen, pressing the bottom nanocom option gives access to the units ID.
2. On to the nanocom website and registered my units I.D. Tip, Mattia is having server problems so just enter the units ID and your email address.
3. Nanocom email you your login and password details to allow you access to the restricted section. On entering the restricted section you are given access to your units licenses. Note them down and take unit back out to car.
4. Plug unit in and go to nanocom tab and select the licenses tab. Enter the codes carefully following this guide:

License1 = unlock box No1
License4 = unlock box No4
License7 = unlock box No7
The amount of licenses you need to enter depends on the version purchased.

5. Once all the licenses have been entered scroll through all the license pages until the last page and save the changes made. Otherwise you have to start again.
6. Unplug nanocom and then re plug in and voilà your nanocom is ready to go.



Hi Merlin,

did you follow the above for unlocking your nanocom? Especially No.5?

Brian.
Post #53666 18th Jan 2011 5:07pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Merlin



Member Since: 30 Oct 2010
Location: Newmarket
Posts: 980
United Kingdom 
Didn’t have any license 7 in my unlock code information.

Merlin
Post #53669 18th Jan 2011 5:09pm
View user's profile Send private message View poster's gallery Reply with quote
Lorryman100



Member Since: 01 Oct 2010
Location: Here
Posts: 2686
They are just examples as the full pack has more licenses than the Td4 pack. Re-install the licenses you have ie, license 2 goes into unlock box no.2 and license 4 goes into unlock box no.4 Thumbs Up Remember to scroll through to the last page to, check the save codes box.
Post #53671 18th Jan 2011 5:13pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Merlin



Member Since: 30 Oct 2010
Location: Newmarket
Posts: 980
United Kingdom 
I’ve done that twice, so I expect that it wasn’t supplied. Guess I have to buy that licence, how?
Merlin
Post #53674 18th Jan 2011 5:19pm
View user's profile Send private message View poster's gallery Reply with quote
Lorryman100



Member Since: 01 Oct 2010
Location: Here
Posts: 2686
What modules do you have access to?
Post #53675 18th Jan 2011 5:20pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Merlin



Member Since: 30 Oct 2010
Location: Newmarket
Posts: 980
United Kingdom 
I’ve just checked and I can’t access AS10 or WABCO ABS. BTW I did go to the end and ‘Save Codes’.
Merlin
Post #53680 18th Jan 2011 5:40pm
View user's profile Send private message View poster's gallery Reply with quote
Lorryman100



Member Since: 01 Oct 2010
Location: Here
Posts: 2686
Right, you have entered one of the codes wrong or have been supplied with the wrong codes for your unit ID Whistle One code does engine and instruments the other 10AS and wabco/ABS. Go back onto nanocom website and recheck you wrote the codes down correctly and have entered them and saved them in the nanocom Thumbs Up
Post #53682 18th Jan 2011 5:44pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Merlin



Member Since: 30 Oct 2010
Location: Newmarket
Posts: 980
United Kingdom 
Hi Lorryman,
You were right about the codes. Got my wife to check the codes with me, and it seems I was putting in a digit one instead of capital I in the licence 2 slot. Censored . I’ve checked that so many times as well. So all works now and thanks for your support. Nucking fuisance this dyslexia.

Merlin
Post #53695 18th Jan 2011 6:23pm
View user's profile Send private message View poster's gallery Reply with quote
Lorryman100



Member Since: 01 Oct 2010
Location: Here
Posts: 2686
Glad to hear you got it working Thumbs Up Was running out of ideas Whistle
Post #53698 18th Jan 2011 6:25pm
View user's profile Send private message View poster's gallery Send e-mail Post Reply
Post Reply  Back to top
Page 3 of 3 <123
All times are GMT + 1 Hour

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums