DEFENDER2.NET - View topic - Head unit and speaker upgrade.

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > In Car Electronics > Head unit and speaker upgrade.

Page 1 of 4

Print this entire topic ·

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Head unit and speaker upgrade.

G'day guys,

I have bought some goodies to upgrade the stereo in 'Ivy'. A Pioneer 8450BT head unit, Vibe lite air 4 components for the front, Vibe slick 6's for the rear and a Pioneer TS-WX110A active sub. I have also bought 2 bulk boxes of Stinger expert roadkill insulation to quieten her and keep the inside a bit cooler.

My question for you, who have been here before (I have looked but can't find a definite answer) is with my crossover for the front components. The factory setup has feed wires to the woofer from the main loom and also feed wires from the loom to the tweeters. when I wire my new crossover do I use the woofer connections and just leave the factory tweeter wires disconnected, I'm right with the new crossover output connections as there labelled

Or.....am I better to run the new crossover feed wires (as it is already wired with heavier wire, enough to reach the head unit) back directly to the head unit. I don' know if I really want to do this but if it is a better option I will.

Thanks

Mick

14th Feb 2013 10:46am

bm52

Member Since: 04 Apr 2010
Location: Kent
Posts: 2189

2014 Defender 110 Puma 2.2 XS CSW Havana

for the sub woofer i put in new wires after advice from an expert. Works very well and quite straightforward to fit. BM52

14th Feb 2013 10:59am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Thanks BM, yes I'm pretty right with the sub, I think, I haven't started the install yet, just nutting everything out before I do. The sub is all RCA connections to the rear of the head unit with a power feed to pick up.

14th Feb 2013 11:04am

Go Beyond

Member Since: 30 Jan 2012
Location: Headcorn, Kent
Posts: 6678

Personally, having spent a considerable sum on the kit and going to the bother of installing sound insulation I would replace ALL of the cables, speaker and power with good quality ones

14th Feb 2013 11:09am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Are you saying new power to the head unit as well, or the separate power feed for the sub which I will be doing anyway.

14th Feb 2013 11:16am

Go Beyond

Member Since: 30 Jan 2012
Location: Headcorn, Kent
Posts: 6678

Only my opinion, but I've taken new power and earth cables up to head unit (and amps) to ensure plenty of ampage and a good quality earth

14th Feb 2013 11:20am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Yep and I appreciate your opinion, its something to think about, I have to get the sub cable under the flooring and up to the dash anyhow.

I suppose I could leave all of the factory wiring in place as well just in case I decided to put back to stock if I sold the car, not likely at this stage though, but ya never know!!!!!

Last edited by Cracka on 17th Feb 2013 1:28am. Edited 1 time in total

14th Feb 2013 11:24am

Go Beyond

Member Since: 30 Jan 2012
Location: Headcorn, Kent
Posts: 6678

I used plastic convoluted tube with a screw on fitting each end (so totally sealed), a hole in battery box end and another in bulkhead to right of steering wheel. Infact I have three running from the bulkhead to various places. Perhaps a bit extreme but makes cable runs clean and easy

14th Feb 2013 11:28am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Do you mean from the battery box under the car into the engine bay then in through the bulkhead.

14th Feb 2013 11:34am

Go Beyond

Member Since: 30 Jan 2012
Location: Headcorn, Kent
Posts: 6678

Yes

There's a few pictures on my FCX 130 thread

14th Feb 2013 12:24pm

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

I did check out those piccies, nice job.

I haven't started the stereo install

.........but I did start the insulation today.....ooh so shiny.

Click image to enlarge

12th Mar 2013 11:28am

custom90

Member Since: 21 Jan 2010
Location: South West, England.
Posts: 20376

Keep up the good work.

Some pictures in my Gallery too that you may find useful although different people have different ways of doing the same thing. All with the same desired outcome though.

$W33T $0U7H3RN $UG4R
🇬🇧🏴󠁧󠁢󠁥󠁮󠁧󠁿🏴󠁧󠁢󠁷󠁬󠁳󠁿🏴󠁧󠁢󠁳󠁣󠁴󠁿🇮🇪🇺🇸⛽️🛢️⚙️🧰💪

12th Mar 2013 11:46am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Thanks Steve. Funny you mentioned the gallery I hadn't even noticed it sitting up there

I got a couple of more sheets on today, I'll just plod along in between other jobs

and get it done.

I was surprised when I removed the rear seats, 28kgs each......the rear lifted 10mm.

Last edited by Cracka on 13th Mar 2013 11:00am. Edited 1 time in total

13th Mar 2013 9:31am

custom90

Member Since: 21 Jan 2010
Location: South West, England.
Posts: 20376

Cracka wrote:
Thanks Steve. Funny you mentioned the gallery I hadn't even noticed it sitting up there

There's a whole gold mine of info on here to help you even by pictures alone. Although no two installs are the same. I would say mine (I'm going to say that aren't I

) and Go Beyond's installs are some of the best I've seen on here along with yours. I especially like how Go-beyond (Matt) has put in fuse boxes ect that he requires for various power feeds so it can all come from one place nice and neat instead of going back to the battery every time which will run out of room. And most importantly safely wired and fused too. Then again he did strip and re-fit nearly everything. My set up is about 70 - 80% complete but still got some bits to sort out.

$W33T $0U7H3RN $UG4R
🇬🇧🏴󠁧󠁢󠁥󠁮󠁧󠁿🏴󠁧󠁢󠁷󠁬󠁳󠁿🏴󠁧󠁢󠁳󠁣󠁴󠁿🇮🇪🇺🇸⛽️🛢️⚙️🧰💪

13th Mar 2013 10:55am

Cracka

Member Since: 08 Dec 2012
Location: New South Wales, Australia
Posts: 129

Yes mate, your'e right about the quality of installs. That's why I haven't put mine in yet, I just haven't got my head into it properly as yet (the wiring side of it). Im running 2 projects at the moment, doing these things to 'Ivy' and I'm also doing a refurb on a boat. I go into the shed and intend to do 1 thing and end up doing bits on each.....its not conducive to getting things done in a timely manner I'm afraid.

13th Mar 2013 11:10am

Page 1 of 4

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum