DEFENDER2.NET - View topic - Removing rear shock insert from top pin mount

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Maintenance & Modifications > Removing rear shock insert from top pin mount

Page 1 of 1

Print this entire topic ·

DC101

Member Since: 01 Jul 2012
Location: Pudsey, West Yorkshire
Posts: 260

Removing rear shock insert from top pin mount

Any tips please. I’ve hit a wall replacing my rear shocks.
The old ones are old -though a new car to me- and though I’ve managed to get the shock body off, the metal insert sleeve inside the bush that fits over the chassis mounting pin is totally seized, though I have got the rest of the shock off.
Any further tips welcomed for its removal. Proving to be a right pain….!

Will I have to replace the mounting bracket:- if so, I’ll have to pick up a couple…but really wanted to crack on with the job. Thanks

Rob

21st Oct 2023 3:01pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3414

2012 Defender 90 Puma 2.2 CSW Santorini Black

Try to get a good gripper or a pipe wrench on the sleeve and see if you can twist it.
Else have to resort to an angle grinder and grind one side of the sleeve until it breaks free. 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

21st Oct 2023 3:33pm

rustandoil

Member Since: 08 Sep 2012
Location: Cotswolds
Posts: 739

2005 Defender 110 Td5 XS DCPU Bonatti Grey

You could try grinding along the side of the bush obviously not touching the mounting pin too much.... Or heat?
Otherwise a new mount, not too expensive

21st Oct 2023 3:34pm

StressedComa

Member Since: 23 Jul 2022
Location: Wakefield
Posts: 64

2011 Defender 90 Puma 2.4 CSW Sumatra Black

I’ve got three used and one new rear shock mounts and not too far away if you decide you want to replace and want one at short notice. Just Pm me.

Chris

21st Oct 2023 4:32pm

Mdm

Member Since: 11 Sep 2013
Location: Sunny Lancashire
Posts: 1601

heat and hope or grind off the old one. it's a common issue

easiest way is take off the shock and bracket and do it on a bench or in a vice. i have spare top brackets over the hill in lancashire if you need a set

21st Oct 2023 7:13pm

DC101

Member Since: 01 Jul 2012
Location: Pudsey, West Yorkshire
Posts: 260

Thanks All.

Really helpful.

Also replacing springs so it’s also been a challenge to remove the bottom retaining plate as totally rusted, but cut through bolts eventually and thankfully had thought ahead to get new plates and bases.

Wish I had done the same with the upper shock mounts…. can anyone tell me what size bolts are also needed here as they are no doubt also going to need cutting off!

Thanks again

Rob

21st Oct 2023 10:03pm

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3414

Your answer in in link below.

https://www.lrworkshop.com/diagrams/land-r...gs_52633#8 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

22nd Oct 2023 5:33am

DC101

Member Since: 01 Jul 2012
Location: Pudsey, West Yorkshire
Posts: 260

Huge thanks to StressedComa, who kindly took time out to drop off two brackets. A gent.
There was no way I was getting the old metal bush sleeves off!

All back together and lesson learnt…(?)

Cheers

23rd Oct 2023 9:16am

Page 1 of 1

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum