| Author |
Message |
 Focal ES100K speaker fitting clarification |
jwb
 17th Oct 2020 7:03pm
|
Forum: In Car Electronics · Replies: 40 · Views: 17818 · Subject: Focal ES100K speaker fitting clarification |
| I went direct to the negative battery terminal with a slightly longer, thicker gauge, wire. |
| Focal ibus how? |
jwb
9th Oct 2020 1:32pm
|
Forum: In Car Electronics · Replies: 26 · Views: 12235 · Subject: Focal ibus how? |
| newton-tony, I think our setups are the same. I used the full range front RCA outputs (R&L) from the head unit, and kept ibus and factory in dash speaker wire (except for new wire from passive cr ... |
| Focal ibus how? |
jwb
29th Sep 2020 6:57pm
|
Forum: In Car Electronics · Replies: 26 · Views: 12235 · Subject: Focal ibus how? |
Paulas,
You may want to double check that your head unit and subwoofer gains and EQ/crossovers are setup correctly. The front/rear 100mm (both OEM and Focal) are a much higher frequency and will ... |
| Focal ibus how? |
jwb
28th Aug 2020 2:34am
|
Forum: In Car Electronics · Replies: 26 · Views: 12235 · Subject: Focal ibus how? |
| Paulas, the 2.1 also includes a 2nd amplifier for 2x55 RMS to front component speakers. I have it in a Far Corners cubby box which works well with standard cubby height but would be a bit tall with a ... |
| Puma 2.4 ROW questions |
jwb
12th Nov 2018 2:09pm
|
Forum: Puma (Tdci) · Replies: 9 · Views: 3972 · Subject: Puma 2.4 ROW questions |
| I agree. You likely do not have an ANR1415 in line next to brake master cylinder. If you look in topix, it will probably show ROW Euro 2 spec as well. |
| Rear Crossmember bolt size |
jwb
16th Jul 2018 1:25am
|
Forum: Maintenance & Modifications · Replies: 8 · Views: 4052 · Subject: Rear Crossmember bolt size |
| I believe they are M10 x 110mm. Usually go through anti-crush spacers inside the crossmember. |
| Upper Rear Body Mounting |
jwb
13th Jul 2018 1:27pm
|
Forum: Puma (Tdci) · Replies: 3 · Views: 1644 · Subject: Upper Rear Body Mounting |
| Hi Mark, I had the same confusion during assembly. Microcat shows bushing but my 08 body did not have them. I didn't pursure adding it at this point and I don't see how it adds value since the brack ... |
| Pop rivets - Rear cappings |
jwb
21st Oct 2016 1:00pm
|
Forum: Maintenance & Modifications · Replies: 8 · Views: 5104 · Subject: Pop rivets - Rear cappings |
| Is there a reason to not use sealed rivets for any body/capping application? |
| Gearbox Rattling Noise... Clutch replaced with HD! :( |
jwb
21st Sep 2016 12:01pm
|
Forum: Puma (Tdci) · Replies: 17 · Views: 10931 · Subject: Gearbox Rattling Noise... Clutch replaced with HD! :( |
| Thank Mark, I didn't realize the puma ceramic paddles were Truckfix, good to know. I wonder how their HD1 style will compare. Unfortunately, it will be a while before I install mine. |
| Gearbox Rattling Noise... Clutch replaced with HD! :( |
jwb
20th Sep 2016 11:44am
|
Forum: Puma (Tdci) · Replies: 17 · Views: 10931 · Subject: Gearbox Rattling Noise... Clutch replaced with HD! :( |
| Gents, you are making me a bit nervous about my recent Truckfix clutch order. I bought their HD1 lined kit which is the most "HD" liner described on their website; it may be ceramic based b ... |
| Storage Solutions for 110 SW 7seat? |
jwb
12th Sep 2016 4:38pm
|
Forum: Puma (Tdci) · Replies: 31 · Views: 14248 · Subject: Storage Solutions for 110 SW 7seat? |
To clarify my prior post, I was suggesting the driver and passenger front floor panel replacement storage boxes from GMB, they hide nicely under the floor mats and are bolt in. Not cheap though.
htt ... |
| Storage Solutions for 110 SW 7seat? |
jwb
10th Sep 2016 11:29am
|
Forum: Puma (Tdci) · Replies: 31 · Views: 14248 · Subject: Storage Solutions for 110 SW 7seat? |
Another alternative for storage of smaller items are the floor safes (left and right) from GMB.
http://www.gmb-mount.de/shop.htm |
| MT82 Input Shaft Seal |
jwb
7th Sep 2016 10:57pm
|
Forum: Puma (Tdci) · Replies: 2 · Views: 1755 · Subject: MT82 Input Shaft Seal |
| Thanks to Dave Ashcroft for his insight. The oil seal should be installed slightly proud, not flush or recessed. |
| MT82 Input Shaft Seal |
jwb
6th Sep 2016 11:54am
|
Forum: Puma (Tdci) · Replies: 2 · Views: 1755 · Subject: MT82 Input Shaft Seal |
Hi all,
I'm installing a MT82 input shaft seal and I do not have the LR special tool to set depth. Does the seal sit flush with the face of the case housing, or is it recessed a few mm? The work ... |
| New AP Clutch - Loose Springs - Video |
jwb
28th Apr 2016 1:01am
|
Forum: Puma (Tdci) · Replies: 5 · Views: 2833 · Subject: New AP Clutch - Loose Springs - Video |
| Thanks Shepherd, I appreciate your insight. Mine is definitely a tambourine when I shake it (similar to the old one I took out), can't see how 2 of the springs would stay in place for very long. Frus ... |
| |
