↓ Advertise on Defender2 ↓

Home > Series Land Rovers > What rims have I got?!
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
LCJ



Member Since: 07 Sep 2009
Location: UK
Posts: 201
What rims have I got?!
Recently bought a 2a which came with horrible 8 spoke wheels. Managed to acquire some steels from eBay but having collected them have to confess I’m not sure what they are! They are 6” wide edge to edge, or 5” internal, and 16” diameter. There is one logo stamped on them (photo below) and two numbers 106363, and 10/54 (a date stamp perhaps?). Can anyone tell me what they are and more importantly what size tyres they’ll take?! Thanks!

Inside:

Click image to enlarge

Logo:

Click image to enlarge
Post #866390 9th Nov 2020 9:15pm
View user's profile Send private message View poster's gallery Reply with quote
Chicken Drumstick



Member Since: 17 Aug 2020
Location: Near MK
Posts: 718
United Kingdom 
Most Land Rover rims will have a part number stamped on them.

As for sizes, depends what you are wanting to do really.

Series rims are 5.5" wide (in terms of bead area). They can fit 7.50 x 16's tyres and smaller. Most tyre makers will suggest a 6.0"j rim for a 235/85R16. So you'd need a 90/Defender rim for this size.

Many Series rims are also tubed rims. Which means it is dangerous and illegal to run a tyre without a tube in it. You can ID this on if there is an extra bulge or not on the bead area of the rim.
Post #866500 10th Nov 2020 11:56am
View user's profile Send private message View poster's gallery Reply with quote
v8bob



Member Since: 14 Mar 2018
Location: Midlands
Posts: 317
United Kingdom 1998 Defender 90 300 Tdi HT Nato Green
The ones shown have the rim riveted to the centre, so they are tube type.
Post #866524 10th Nov 2020 2:36pm
View user's profile Send private message View poster's gallery Reply with quote
blackwolf



Member Since: 03 Nov 2009
Location: South West England
Posts: 17372
United Kingdom 2007 Defender 110 Puma 2.4 DCPU Stornoway Grey
Traditionally rims for SWB models were 5" whilst those for LWB were 5.5" I think. SWBs had 6.00x16 tyres whilst LWBs had 7.50x16 tyres.
Post #866527 10th Nov 2020 3:29pm
View user's profile Send private message View poster's gallery Reply with quote
LandRoverAnorak



Member Since: 17 Jul 2011
Location: Surrey
Posts: 11324
United Kingdom 
Wheel rim width is measured inside of the two rims so if you've measured what I think you've measured, you have some standard SWB wheels. As v8bob says, they're for tubed tyres.



Some very early models had 4.5 inch wide rims but they're really not very common. Darren

110 USW BUILD THREAD - EXPEDITION TRAILER - 200tdi 90 BUILD THREAD - SANKEY TRAILER - IG@landroveranorak

"You came in that thing? You're braver than I thought!" - Princess Leia
Post #866606 10th Nov 2020 9:57pm
View user's profile Send private message View poster's gallery Reply with quote
LCJ



Member Since: 07 Sep 2009
Location: UK
Posts: 201
Thanks for all the responses. I posted the same question on the S2 forum and the consensus there seems to be that they are Kelsey Hayes wheels, and most likely for a trailer or other lighter vehicle. Given that and the fact they're for tubes means I probably won't use them on my car, so if anyone wants them and can collect from Haslemere, Surrey, they're free to a good home!
Post #866666 11th Nov 2020 9:28am
View user's profile Send private message View poster's gallery Reply with quote
Chicken Drumstick



Member Since: 17 Aug 2020
Location: Near MK
Posts: 718
United Kingdom 
tbh the easiest way for Land rover 'looking' rims. Is to buy some for a 90/Defender. They will fit straight on, are wide enough for a 235/85 and are tubeless. Should also be easy and cheap to pick up.
Post #866678 11th Nov 2020 10:13am
View user's profile Send private message View poster's gallery Reply with quote
blackwolf



Member Since: 03 Nov 2009
Location: South West England
Posts: 17372
United Kingdom 2007 Defender 110 Puma 2.4 DCPU Stornoway Grey
LandRoverAnorak wrote:
... Some very early models had 4.5 inch wide rims but they're really not very common.


I didn't mention them in my post because they are so rare and collectible (like the original pattern of 543384 or genuine 569203 rims)! Or genuine S1 split rims, for that matter.
Post #866685 11th Nov 2020 10:46am
View user's profile Send private message View poster's gallery Reply with quote
LCJ



Member Since: 07 Sep 2009
Location: UK
Posts: 201
Chicken Drumstick wrote:
tbh the easiest way for Land rover 'looking' rims. Is to buy some for a 90/Defender. They will fit straight on, are wide enough for a 235/85 and are tubeless. Should also be easy and cheap to pick up.


Thanks, that's what I'm aiming to do - just these were cheap and local so thought they might be worth a punt!
Post #866687 11th Nov 2020 10:57am
View user's profile Send private message View poster's gallery Reply with quote
22900013A



Member Since: 23 Dec 2010
Location: Oxfordshire
Posts: 3149
United Kingdom 2011 Defender 110 Puma 2.4 USW Keswick Green
Chicken Drumstick wrote:
tbh the easiest way for Land rover 'looking' rims. Is to buy some for a 90/Defender. They will fit straight on, are wide enough for a 235/85 and are tubeless. Should also be easy and cheap to pick up.


No they aren't. Standard Defender rims are only 5.5" wide, suitable for sizes upto 7.50R16. 235/85R16 will require wider rims such as wolf rims or alloys. 2011 110 USW
1973 Series III 1-Ton
1972 Series III 1-Ton Cherrypicker
1969 IIA 1-Ton
1966 IIA 88"
Post #868370 19th Nov 2020 5:55pm
View user's profile Send private message View poster's gallery Send e-mail Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums