DEFENDER2.NET - View topic - Turbo actuator plug

↓ Advertise on Defender2 ↓

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Puma (Tdci) > Turbo actuator plug

Page 1 of 1

Print this entire topic ·

Primaryroo

Member Since: 15 Aug 2020
Location: kent
Posts: 20

2008 Defender 110 Puma 2.4 CSW Alpine White

Turbo actuator plug

Morning everybody, i wonder if anybody can give me some advice, bought a 2008 110 ( love her) drove about 300 mile then fault light came on. so as usual ordered a nanocom unit checked code and it was turbo over pressure,
once back in my garage and embarking on new swivel kits and balls and steering bars and steering box.....got to love it i checked the actuator nothing was happening. i gripped the wires to the plug and it stated moving ( broken wire ) rebuilt plug and took her to pick up my new caravan. she ran like a dream apart from smoke for the first mile then nothing.
picked caravan up and she drove like nothing was on the back. anyway after a long hill along the motorway she just lost power completely all gauges went mental so pulled over plugged nanocom in and turbo over pressure / high temp air inlet ....cleared code and tried to start and she sounded like a 2 stroke needing more choke, turned off and back on and she was 100% after 19 mile it done it again but after 10 seconds she was fine.
l left nanocom plugged in and she was reaching 110 c on hills then dropping to 89 instantly after hills.

my thoughts are

1. crap from turbo has fouled egr
2. egr heating water too much

can i get a patch to blank egr through nanocom and delete mechanivally and softwary lol

or is this something else.......head gasket seems fine lots of pressure

any thought would be greatly appreciated series 2a 1966
defender 90 1991
discovery 3 2005
discovery 2 2003
defender puma 110 2008
defender puma ex scottish power 2.4 2011

13th Sep 2020 5:14am

Dinnu

Member Since: 24 Dec 2019
Location: Lija
Posts: 3414

2012 Defender 90 Puma 2.2 CSW Santorini Black

This thread might help: https://www.defender2.net/forum/topic73806...verheating

I would investigate why the temperature is climbing to 110dC first and foremost. since temperature drops to 90dc when there is less load, then it points to poor heat dissipation.. check radiator for clogging with leaves, dirt etc.
Good to check the viscous coupling on the radiator fan making sure that it draws enough air.
Coolant level is correct. 1988 90 Hard Top, 19J Diesel Turbo, Shire Blue - Restoration ongoing
2012 90 CSW, 2.2TDCI, Santorini Black

13th Sep 2020 5:34am

jst

Member Since: 14 Jan 2008
Location: Taunton
Posts: 8021

2011 Defender 110 Puma 2.4 USW Stornoway Grey

Is it getting hot due to excess fuel incease in egt from turbo issues still. What boost is being made at fault occurrence point? Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop

13th Sep 2020 9:18am

Primaryroo

Member Since: 15 Aug 2020
Location: kent
Posts: 20

well got bored and investigated.
took rad out cleaned through outside and in, loads of mud in veins
changed fluid to high quality coolant
changed water pump
changed thermostat (original 2007)

found after searching online and found exact same thermostat for MG temp 78 degree (havent fitted ,,,,a just in case thingy

temp is now 10 degree lower and towed caravan, temp didnt go above 92 even going up steep long hill

temp gauge is physically lower on needle

fingers crossed ( also now have plugged egr back in so thats back in the loop )

it still cools down instanltly when load finnished (but am i being overly concerned due to nanocom instantly updating temp ) series 2a 1966
defender 90 1991
discovery 3 2005
discovery 2 2003
defender puma 110 2008
defender puma ex scottish power 2.4 2011

29th Sep 2020 5:40am

hank

Member Since: 12 Sep 2016
Location: South Wales
Posts: 2298

2007 Defender 110 Puma 2.4 DCPU Stornoway Grey

Hope you've got it sorted. If it reoccurs have a look at my post here about "P0234-00 (28 ) turbo overboost condition" error and the steps I took to sort it

https://www.defender2.net/forum/topic53240-113.html > 110 XS Double Cab

29th Sep 2020 8:20am

Page 1 of 1

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum