↓ Advertise on Defender2 ↓

Home > Puma (Tdci) > Puma swivel grease level
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
macfrank



Member Since: 05 Nov 2015
Location: somewhere in the north
Posts: 1072
Germany 2015 Defender 110 Puma 2.2 SW Keswick Green
Puma swivel grease level
As I suspect a swivel grease leak on the right (offside), I tried to measure the grease level.
Somewhere I read it should be about 5cm when sticking a tent peg into the swivel housing.
Is that correct?
As you can see below, I only have about 1.5cm but it's about the same on both sides
(My 2015, 40kkm).

Here are some pics of the process, maybe of use to someone:

0) returning home from holiday and after a (careful) pressure wash:

Click image to enlarge


carefully removed dirt and waxoil-like rust protection wax...

1) axle stands, no need to remove tyres, 3/8" ratchet extension:

Click image to enlarge

2) turn wheels to full lock to move the swivel ball away from the plug, note bit of rust on the thread, looking inside you can see the CV joint's ABS ring - and some grease - good Smile

Click image to enlarge

3) tent peg down the hole - is that enough grease? similar on the left (nearside)

Click image to enlarge



4) filled up with just a little grease, but will keep checking

Click image to enlarge

5) a short trip showed no leak yet, but there's still dirt
note the swivel seal Land Rover put into this late Defender: it's missing an outer seal to keep the dirt away from the inner one... I've already ordered new ones and even the 3€ allmakes seal does have that additional lip...

Click image to enlarge

Frank
Post #860666 9th Oct 2020 3:34pm
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8021
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
Just whack a load in, any cv grease works, buy it in cartridge grease gun style cases, its cheaper and easier to add. To check it with a tent peg it would have to hot enough to be in liquid form surely? Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #860673 9th Oct 2020 4:12pm
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8021
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
Thank you for your pm, sorry I bothered to try and help. Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #860700 9th Oct 2020 6:37pm
View user's profile Send private message View poster's gallery Reply with quote
ozzie1989



Member Since: 25 Feb 2009
Location: Wales
Posts: 282
Wales 2010 Defender 110 Puma 2.4 USW Bonatti Grey
In my experience they only leak when one or both bearings are worn/wearing leaving a gap between the seal and cup, or when the cup gets damaged/scored.

Well worth checking the bearing preload is set properly using the shims as per the workshop manual.

As for the grease, pointless measuring it as it's not in liquid form. When empty you use one sachet/tube of one shot grease. Maybe go for half a tube as it looks like you've lost a fair bit. Now: 2010 2.4 TDCi 110 Utility Wagon
Then: 2004 2.5 TD5 90 Hard Top (X-Tech Edition)
Post #860710 9th Oct 2020 7:09pm
View user's profile Send private message View poster's gallery Reply with quote
Pacha



Member Since: 23 Feb 2020
Location: North Yorkshire
Posts: 772
United Kingdom 2008 Defender 90 Puma 2.4 HT Stornoway Grey
jst wrote:
Thank you for your pm, sorry I bothered to try and help.


Rolling with laughter Rgds.

Chris
Post #860712 9th Oct 2020 7:20pm
View user's profile Send private message View poster's gallery Reply with quote
jst



Member Since: 14 Jan 2008
Location: Taunton
Posts: 8021
 2011 Defender 110 Puma 2.4 USW Stornoway Grey
ozzie1989 wrote:
In my experience they only leak when one or both bearings are worn/wearing leaving a gap between the seal and cup, or when the cup gets damaged/scored.

Well worth checking the bearing preload is set properly using the shims as per the workshop manual.

As for the grease, pointless measuring it as it's not in liquid form. When empty you use one sachet/tube of one shot grease. Maybe go for half a tube as it looks like you've lost a fair bit.


i wouldnt bother, you will get a PM telling you your wrong. Cheers

James
110 2012 XS Utility
130 2011 M57 bespoke Camper
90 2010 Hardtop
90 M57 1988 Hardtop
Post #860717 9th Oct 2020 7:26pm
View user's profile Send private message View poster's gallery Reply with quote
williamthedog



Member Since: 29 Dec 2012
Location: south wales
Posts: 3441
2011 Defender 90 Puma 2.4 PU Tamar Blue
Why did he ask for advice then? Rolling with laughter Rolling with laughter Rolling with laughter
Post #860725 9th Oct 2020 8:05pm
View user's profile Send private message View poster's gallery Reply with quote
macfrank



Member Since: 05 Nov 2015
Location: somewhere in the north
Posts: 1072
Germany 2015 Defender 110 Puma 2.2 SW Keswick Green
He is still asking for advice... Otherwise, would I have started this thread??
I won't comment on jst's.
Post #860733 9th Oct 2020 8:23pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
DEFENDER2.NET RSS Feed - All Forums